Error Code ေလး သိရင္ပိုေကာင္းပါတယ္ .. ဘယ္က ျဖစ္လဲ သိႏိုင္ပါတယ္
ဒီေအာက္မွာ သူနဲ႔ သက္ဆိုင္တဲ့ Code ေတြပါ .. ဟုတ္မလားေတာ့ မသိပါဘူး ေျပာၾကည့္တာပါ .. မွားရင္လည္း ခြင့္လႊတ္ေနာ္STOP: 0x0000000A
This Stop error, which can be caused by either software or
hardware, indicates that a kernel-mode process or driver attempted to access a
memory location it did not have permission to access or a memory location that
exists at a kernel interrupt request level (IRQL) that was too high. A
kernel-mode process can access other only processes that have an IRQL that's
equal to or lower than its own.
Troubleshooting a Stop 0x0000000A error in Windows XPSTOP: 0x0000001E
This Stop error indicates that indicates that the Windows XP
kernel detected an illegal or unknown processor instruction. The problems that
cause this Stop error can be either software or hardware related and result
from invalid memory and access violations, which are intercepted by Windows'
default error handler if error-handling routines are not present in the code
Possible Resolutions to STOP 0x0A, 0x01E, and 0x50 ErrorsSTOP: 0x00000050
This Stop error indicates that requested data was not in
memory. The system generates an exception error when using a reference to an
invalid system memory address. Defective memory (including main memory, L2 RAM
cache, video RAM) or incompatible software (including remote control and
antivirus software) might cause this Stop error.
Possible Resolutions to STOP 0x0A, 0x01E, and 0x50 ErrorsSTOP: 0x0000007B
This Stop error indicates that Windows XP has lost access to
the system partition or boot volume during the startup process. Installing
incorrect device drivers when installing or upgrading storage adapter hardware
typically causes this Stop error. This error could also indicate a possible
Troubleshooting Stop 0x0000007B or "0x4,0,0,0" ErrorSTOP: 0x0000007F
This Stop error indicates a hardware problem resulting from
mismatched memory, defective memory, a malfunctioning CPU, or a fan failure
that's causing overheating.
General causes of "STOP 0x0000007F" errorsSTOP: 0x0000009FDRIVER_POWER_STATE_FAILURE
This Stop error indicates that a driver is in an
inconsistent or invalid power state. This Stop error typically occurs during events
that involve power state transitions, such as shutting down, or moving in or
out of standby or hibernate mode.
Troubleshooting a Stop 0x9F Error in Windows XPSTOP: 0x000000D1 DRIVER_IRQL_NOT_LESS_OR_EQUAL
This Stop error indicates that the system attempted to
access pageable memory using a kernel process IRQL that was too high. The most
typical cause is a bad device driver (one that uses improper addresses). It can
also be caused by faulty or mismatched RAM or a damaged pagefile.
Error Message with RAM Problems or Damaged Virtual Memory ManagerSTOP: 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVER
This Stop error indicates that a device driver problem is
causing the system to pause indefinitely. Typically, this problem is caused by
a display driver waiting for the video hardware to enter an idle state. This
might indicate a hardware problem with the video adapter or a faulty video
Error message: STOP 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVERSTOP: 0x00000024 NTFS_FILE_SYSTEM
This Stop error indicates that a problem occurred within Ntfs.sys, the driver file that allows the system to read
and write to drives formatted with the NTFS file system. (A similar Stop
message, 0x00000023, exists for the file allocation table [FAT16 or FAT32)]
Troubleshooting Stop 0x24 or NTFS_FILE_SYSTEM Error MessagesSTOP: 0xC0000218UNKNOWN_HARD_ERROR
This Stop error indicates that a necessary registry hive
file could not be loaded. The file may be corrupt or missing. The registry file
may have been corrupted due to hard disk corruption or some other hardware
problem. A driver may have corrupted the registry data while loading into
memory or the memory where the registry is loading may have a parity error.
Troubleshoot a Stop 0xC0000218 Error MessageSTOP: 0xC0000221STATUS_IMAGE_CHECKSUM_MISMATCH
This Stop message indicates driver, system file, or disk
corruption problems (such as a damaged paging file). Faulty memory hardware can
also cause this Stop message to appear.
"STOP: C0000221 unknown hard error" or "STOP: C0000221 STATUS_IMAGE_CHECKSUM_MISMATCH" error message occurs
ဒီမွာ မူရင္း ဆိုဒ္ပါ ...[You must be registered and logged in to see this link.]